/dev/console not found nach dump/restore

Markus Wigge markus at cultcom.de
Thu Feb 9 16:41:42 CET 2006


Hi,

> > die initrd scheint "ide_generic" nicht zu laden?!
> 
> ide_generic ist der generische ide-pci driver. Wenn du einen besseren
> hast dann muss der ide-generic auch nicht laden ...
tja, ohne komme ich nicht an die Platte, d.h. wohl das ich den
Brauche.

> > Meine Idee den root-Parameter direkt auf "/dev/hdc2" zu setzten hat übrigens
> > wie erwartet keine Besserung gebracht.
> 
> Ohne genauere aussage ueber die fehlermeldung - evtl ein komplettes
> bootlog (serielle console  hint hint) kann man aus der ferne nichts
> diagnostizieren.
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000005fff0000 (usable)
 BIOS-e820: 000000005fff0000 - 000000005fff8000 (ACPI data)
 BIOS-e820: 000000005fff8000 - 0000000060000000 (ACPI NVS)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
639MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fbe00
DMI 2.3 present.
ACPI disabled because your bios is from 97                         and too old
You can enable it with acpi=force
Intel MultiProcessor Specification v1.1
    Virtual Wire compatibility mode.
OEM ID: EZHI     Product ID: IDOT-MP      APIC at: 0xFEE00000
Processor #0 6:8 APIC version 17
Processor #1 6:8 APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Processors: 2
Built 1 zonelists
Kernel command line: root=/dev/md1 ro console=ttyS0,9600n8
Initializing CPU#0
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 999.958 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1550528k/1572800k available (1663k kernel code, 21128k reserved, 772k data, 168k init, 655296k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1568.76 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel Pentium III (Coppermine) stepping 0a
per-CPU timeslice cutoff: 731.73 usecs.
task migration cache decay timeout: 1 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000084
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 3000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1994.75 BogoMIPS
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Pentium III (Coppermine) stepping 0a
Total of 2 processors activated (3563.52 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
..TIMER: vector=0x31 pin1=2 pin2=0
testing the IO APIC.......................
Using vector-based indexing
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 999.0523 MHz.
..... host bus clock speed is 133.0269 MHz.
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4752k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfdb71, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f76a0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x6844, dseg 0xf0000
PnPBIOS: 11 nodes reported by PnP BIOS; 11 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0686] at 0000:00:07.0
PCI->APIC IRQ transform: (B0,I7,P3) -> 129
PCI->APIC IRQ transform: (B0,I8,P0) -> 129
PCI->APIC IRQ transform: (B0,I9,P0) -> 81
PCI->APIC IRQ transform: (B0,I10,P0) -> 65
PCI->APIC IRQ transform: (B0,I11,P0) -> 121
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
PCI: Enabling Via external APIC routing
PCI: Via IRQ fixup for 0000:00:07.2, from 11 to 1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 16384 buckets, 128Kbytes
TCP: Hash tables configured (established 524288 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4752 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 168k freed
initrd-tools: 0.1.81.1
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
SCSI subsystem initialized
sym0: <875> rev 0x26 at pci 0000:00:0b.0 irq 121
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.18j
Using anticipatory io scheduler
  Vendor: ACARD     Model: MirrorSmart 37G   Rev: 2.6I
  Type:   Direct-Access                      ANSI SCSI revision: 02
scsi(0:0:13:0): Beginning Domain Validation
sym0:13: wide asynchronous.
scsi(0:0:13:0): Wide Transfers Fail
sym0:13: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 8)
scsi(0:0:13:0): Domain Validation skipping write tests
scsi(0:0:13:0): Ending Domain Validation
SCSI device sda: 78165359 512-byte hdwr sectors (40021 MB)
SCSI device sda: drive cache: write back
 /dev/scsi/host0/bus0/target13/lun0: p1 p2 p3
Attached scsi disk sda at scsi0, channel 0, id 13, lun 0
Generic RTC Driver v1.07
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
parport_pc: VIA parallel port disabled in BIOS
e100: Intel(R) PRO/100 Network Driver, 3.0.18
e100: Copyright(c) 1999-2004 Intel Corporation
e100: eth0: e100_probe: addr 0xdff6d000, irq 81, MAC addr 00:03:A8:01:0F:B3
e100: eth1: e100_probe: addr 0xdff6c000, irq 65, MAC addr 00:03:A8:03:0F:B3
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:07.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:07.2: irq 129, io base 0000dc00
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA Apollo Pro 133 chipset
agpgart: Maximum main memory to use for agp memory: 1430M
agpgart: AGP aperture is 64M @ 0xe0000000
input: PC Speaker
pivot_root: No sKernel panic: Attempted to kill init!
uch file or dire

------------------------
das ist über seriell etwas zerstückelt, auf der Konsole sehen die letzten
Zeilen so aus:

input: PC Speaker
pivot_root: No such file or directory
/sbin/init: 432: cannot open dev/console: No such file
Kernel panic: Attempted to kill init!


Was mich etwas verwundert ist der relative Pfad "dev/console", ich
hätte da "/dev/console" erwartet.
Außerdem vermisse ich Meldungen zu "/dev/hdc", er lädt scheinbar nur
einen E-IDE-Treiber scannt/findet aber keine devices?


ich hoffe da wird einer schlauer draus als ich...

Gruß,
  Markus




More information about the Linux mailing list